Setting up A Bathtub
Setting up A Bathtub
Blog Article
In this article in the next paragraph you will find a lot of professional insight regarding A Step-by-Step Guide to Installing a Bathtub.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately difficult project. If the old tub is readily accessible, the task can relocate easily; if you need to open up a wall to remove the old tub as well as position the new tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have qualified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your shower room if you have already bought a brand-new bathtub and also do not need to change the arrangement of your previous water pipelines.
Your devices as well as material list need to make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite problematic as a result of the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Secure the faucet in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using both wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water as well as check all joints and new pipework for leaks and tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet as well as the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has been used at the very least when as this will certainly settle it into its last placement.
Getting ready for the Installation
Firstly, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about How to Install a Bathtub from someone on another domain. Do you know about somebody who is intrigued by the subject? Take a moment to share it. Thank you for your time spent reading it.
See Availability
Report this page